How to perform the wireless LAN setup manually (Windows)
21-Dec-2015
8201024000
Solution
- Before performing the wireless setup
Regarding the preparations and the procedures for using the printer in a wireless connection, refer to [ The necessary environment and the procedures for using the printer in a wireless connection ].
- The information you need to have, in order to complete the wireless LAN setup manually.
In most cases, "Easy Setup" will be used to connect the machine to your access point or router.
Before you continue, you must gather the following information which will be required during the installation.
REFERENCE
For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.
- Access Point Name/Network Name
* Also referred to as SSID.
An identifier to identify the specific access point.
- Network Key
* Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.
A password to prevent unauthorized access to the network.
1.
(1) Press the Setup button (A).
(2) Use the 
or 
button (B) to select Wireless LAN setup.
or button (B) to select Wireless LAN setup.(3) Press the OK button.
2.
Use the 
or 
button (C) to select Yes, then press the OK button.
or button (C) to select Yes, then press the OK button.
When wireless connection is enabled, the Wi-Fi lamp (D) lights blue.
3.
Select Easy setup, then press the OK button.
4.
Select the access point name you wrote down, then press the OK button.
REFERENCE
- If you are living in an apartment, access points in use nearby may also be detected.
- The access point names with 2-byte characters are not displayed properly, however, can be selected.
5.
Make sure that one of the above screens is displayed, then press the OK button.
If the above screen is not displayed, go to 8.
6.
Enter the network key you wrote down , then press the left FUNCTION button (E).
Press the center FUNCTION button (F) to switch character entry modes.
IMPORTANT
Network key entry is case-sensitive. Be sure to enter upper and lower case letters correctly.
REFERENCE
- Character Entry
This machine allows you to enter characters when an on-screen keyboard is displayed.
Follow the procedure below.
1. When an on-screen keyboard shown above is displayed, press the center FUNCTION button (F) to switch to a keyboard having characters you want to use.
- Three character sets are available: Upper-case alphabets, lower-case alphabets, numbers and symbols. Each time you press the center FUNCTION button, an on-screen keyboard is switched among them.
2. Select a character on the on-screen keyboard using the 
buttons (G), then press the OK button to enter it.
buttons (G), then press the OK button to enter it.- Entered characters are displayed on the upper section (H) of the on-screen keyboard.
3. Repeat 1 and 2 to enter more characters.
4. After you enter all characters you need, press the left FUNCTION button (E).
* To insert a space, select Space on the on-screen keyboard and press the OK button.
* To insert characters, select the section (H) of the screen using the or button, move the cursor to the character on the right of the target position using the or button, then enter characters.
or button, move the cursor to the character on the right of the target position using the or button, then enter characters.* To delete a character, select the section (H) of the screen using the or button, move the cursor to the target character using the or button, then press the right FUNCTION button (I).
or button, move the cursor to the target character using the or button, then press the right FUNCTION button (I).7.
Make sure that the network key is correct, then press the left FUNCTION button.
8.
When the above screen appears, press the OK button.
REFERENCE
- If Failed to connect to the access point. appears, press the OK button, make sure that the network key is correct, then enter it again. If a connection still cannot be established, refer to the printed manual: Network Setup Troubleshooting.
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer’s hard disk.
The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application software to be installed.)
IMPORTANT
- Quit all running applications before installation.
- If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.
- Log on as the administrator (or a member of the Administrators group).
- Do not switch users during the installation process.
- Internet connection may be required during the installation. Connection fees may apply. Consult the internet service provider.
- It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the Setup CD-ROM during restart. The installation resumes once your computer has restarted.
REFERENCE
- Easy-WebPrint EX
Easy-WebPrint EX is Web print software that is installed on the computer when installing the supplied software.
Internet Explorer 7 or later (Windows) is required to use this software. An Internet connection is required for installation.
1.
Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.
If you are using Windows, the setup program starts automatically.
REFERENCE
If the program does not start automatically, double-click the CD-ROM icon in Computer or My Computer.
When the CD-ROM contents appear, double-click MSETUP4.EXE.
2. Windows 7/Windows Vista
Windows XP -> 3
Click Run Msetup4.exe on the AutoPlay screen, then click Yes or Continue on the User Account Control dialog box.
If the User Account Control dialog box reappears in following steps, click Yes or Continue.
3.
Select your place of residence, then click Next.
REFERENCE
If the Select Language screen appears, select a language, then click Next.
4.
Select a country or region, then click Next.
5.
Click Easy Install.
The drivers, application software, and on-screen manuals are installed.
REFERENCE
If you want to select particular items to install, click Custom Install.
6.
Click Install.
7.
Select Use the printer with wireless LAN connection, then click Next.
Follow any on-screen instructions to proceed with the software installation.
8.
When the Printer Detection screen appears, click Next.
9.
When the Detected Printers List dialog box appears, select Canon MX xxx series, then click Next.
REFERENCE
XXX: xxx refers to the model name you are using.
IMPORTANT
- When this printer has not been detected, the Check Printer Settings dialog box is displayed. In such a case, refer to [ The printer cannot be detected (the message that the printer could not be detected on the network is displayed) ].
10.
When the Setup Completion dialog box appears, click Complete.
1.
Click Next.
Follow any on-screen instructions to proceed with the software installation.
- Important Information for the Installation
If the serial number is not displayed on the registration screen, input the number found inside the machine.
IMPORTANT
- If the power is on, the Print Head Holder will move when the Scanning Unit (Cover) (A) is opened.
REFERENCE
The User Registration screen will only be displayed when Europe, Middle East, Africa is selected on the Select Your Place of Residence screen.
- If the Extended Survey Program screen appears
If you can agree to Extended Survey Program, click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine’s functionality.)
2.
Click Exit to complete the installation.
3.
Solution Menu EX starts.
Remove the Setup CD-ROM and keep it in a safe place.
REFERENCE
The buttons displayed on Solution Menu EX may vary depending on the country or region of purchase.
The end of the procedure of the wireless LAN setup.