How to install the MP drivers
29-Feb-2008
8100146700
Solution
REFERENCE
Explanation below is given with an example using MX7600.
NOTE
- The screens below refer to Windows Vista™ operating system Ultimate Edition (hereafter referred to as "Windows Vista") installation. Screens may vary depending on the operating system you are using.
- Quit all running applications before installation.
- Log into a user account with the administrator privilege.
- Do not switch users during the installation process.
- A message asking for your confirmation to restart your computer may appear during the installation process. If this message is displayed, follow the on-screen instructions and click OK. The installation resumes from where it left off when your computer has been restarted. While restarting, do not remove the Setup CD-ROM.
1. Be sure to TURN THE MACHINE OFF before continuing.
1-1. Press the ON/OFF button.
1-2. Make sure that all the lamps on the Operation Panel have gone out.
2. Turn the computer on and start Windows.
IMPORTANT
If the Found New Hardware or Found New Hardware Wizard screen appears automatically, remove the USB cable connected to your computer. Click Cancel to quit the screen. In Windows Vista, the screen may close automatically when the USB cable is unplugged. Then turn off the machine and proceed from Step 3. to install the software.
3. Insert the Setup CD-ROM.
The setup program should run automatically.
In Windows Vista, go to Step 4. In Windows XP and Windows 2000, go to Step 6.
NOTE
If the setup program does not run automatically, refer to "Cannot Install the MP Drivers" .
4. If the AutoPlay screen appears, click Run Msetup4.exe.
This screen will not appear in Windows XP and Windows 2000.
5. If the User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue.
This screen will not appear in Windows XP and Windows 2000.
6. When the main menu appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed automatically.
NOTE
If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed with the installation.
7. When the list of applications to install appears, confirm the contents, then click Install.
NOTE
Move the cursor over items to display explanations of each application.
8. Read the License Agreement carefully and click Yes. The software installation screen may appear during the installation process. Read the contents on the screen and follow the onscreen instructions to install the software.
9. Read the License Agreement carefully and click Yes. The software installation screen may appear during the installation process. Read the contents on the screen and follow the onscreen instructions to install the software.
10. When the Printer Connection screen appears, connect one end of the USB cable to the computer, the other to the machine, then TURN THE MACHINE ON.
When you turn on the machine, the COPY button flashes green, then remain lit.
The software will begin identifying the printer port being used.
IMPORTANT
If you cannot go to the next procedure after three minutes, refer to "Cannot Install the MP Drivers".
11. When the Setup Complete screen appears, click Next.
12. When the User Registration screen appears, click Next.
NOTE
To register later, click Cancel and go to Step 13. After software installation is complete, double-click 
on the desktop.
on the desktop.If your network is connected to the Internet, the registration screen will appear.
Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.
13. When the PIXMA Extended Survey Program screen appears, confirm the message. We would appreciate it if you would take part in the PIXMA Extended Survey Program regarding the use of Canon printers. If you can agree, click Agree.
If Do not agree is clicked, the PIXMA Extended Survey Program will not be installed but you can use the machine normally.
14. When the Installation completed successfully screen appears, click Exit.
The Setup CD-ROM will be ejected.
If it is not ejected automatically, remove it manually.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CD-ROM.
NOTE
Keep the CD-ROM in a safe place in case you need to reinstall the software.
Software installation is now complete.
Setting Up the Machine and the Computer (Windows)
To use the machine connected to a computer, you need to install the software called "MP Drivers" in the computer.
[ Setting Up for Use over Wired LAN ]
(A) This machine
(B) Hub or router
(C) Computer
When the machine has not been connected to the network, perform this setup to use the machine over wired LAN. This setup procedure requires settings to be performed on the machine and the computer.
NOTE
- To set up the machine that is not yet connected to a wired LAN, connect the machine and the computer with a USB cable.
- Even if the machine has been set up to be used with the USB connection, follow the setup procedure described in this manual to connect the machine to a wired LAN for the first time.
[ Setting Up an Additional LAN-connected Computer ]
(A) This machine
(B) Hub or router
(C) Connected computer
(D) Additional computer
When the machine has already been set up to connect to the network, perform this setup to use the machine from an additional computer over wired LAN. This setup procedure only requires settings to be performed on the additional computer.
1. Preparing for Setup.
Before installing the MP Drivers in your computer, make sure of the following.
- If the installation and adjustment of the machine have not been finished, refer to your setup sheet to set up the machine properly.
- Turn off the firewall function temporarily or change its setting. If you disable the firewall function, disconnect your network from the Internet. For information on the firewall function of your security software, refer to its instruction manual or contact its manufacturer.
IMPORTANT
After setup is complete, turn back on the firewall function you disabled for setup.
If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.
- Make sure that the configuration of computers, hubs, and other network devices is complete, and computers can connect to the network. The configuration and the type of the device vary depending on your network environment. For details, refer to your device’s instruction manual or contact its manufacturer.
IMPORTANT
A hub and LAN cable are required to connect this machine to a wired LAN. These must be purchased separately.
IMPORTANT
Depending on the country or region of purchase, the following two CD-ROMs are included in the package for the Windows setup.
– Windows (CD-1)
– Windows (CD-2) Macintosh
In this case, insert the Setup CD-ROM "Windows (CD-1)" first to start the installation, and follow the onscreen instructions to complete the installation.
NOTE
- In an office setup, consult your network administrator.
- Quit all running applications before installation.
- Log into a user account with the administrator privilege.
- Do not switch users during the installation process.
- A message asking for your confirmation to restart your computer may appear during the installation process. If this message is displayed, follow the on-screen instructions and click OK. The installation resumes from where it left off when your computer has been restarted. While restarting, do not remove the Setup CD-ROM.
The screens in this manual refer to Windows Vista™ operating system Ultimate Edition (hereafter referred to as "Windows Vista") installation. Screens may vary depending on the operating system you are using and also depending on the country or region of purchase.
2. Installing the Software.
NOTE
Wizard screen appears automatically during the installation process, remove the USB cable connected to your computer.
Click Cancel to quit the screen. In Windows Vista, the screen may close automatically when the USB cable is unplugged.
Then turn off the machine and proceed from step 3. to install the software.
2-1. Turn off the machine.
NOTE
Confirm that all the lamps on the Operation Panel have gone out.
2-2. Turn the computer on and start Windows.
2-3. Insert the Setup CD-ROM.
The setup program should run automatically.
If the setup program does not run automatically, see "Installation does not start automatically when the Setup CD-ROM is inserted into your computer's disc drive." in "Cannot Install the MP Drivers" .
In Windows Vista, go to step 4.
In Windows XP and Windows 2000, go to step 6.
IMPORTANT
If two CD-ROMs are included in the package for the Windows setup, insert the Setup CD-ROM "Windows (CD-1)".
NOTE
- If the Select Language screen appears, select a language, then click Next.
- If the Select Your Place of Residence screen appears, select your place of residence, then click Next.
2-4. If the AutoPlay screen appears, click Run Msetup4.exe.
This screen will not appear in Windows XP and Windows 2000.
2-5. If the User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.
This screen will not appear in Windows XP and Windows 2000.
NOTE
- If the Select Language screen appears, select a language, then click Next.
- If the Select Your Place of Residence screen appears, select your place of residence, then click Next.
2-6. When the screen shown on the right appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed automatically.
NOTE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.
2-7. When the Easy Install screen appears, confirm the contents, then click Install.
NOTE
- Move the cursor over items to display explanations of each application.
- The list of applications may vary depending on the country or region of purchase.
Users in Asia
- Scan Soft OmniPage SE can be installed only on an English operating system.
2-8. Read the License Agreement carefully and click Yes.
Installation of the MP Drivers, On-screen Manuals, and application software will begin.
The software installation screen may appear during the installation process. Read the contents on the screen and follow the on-screen instructions to install the software.
2-9. When the Setup Method screen appears, confirm the connection type.
The next procedure varies depending on how you intend to connect the machine and the computer.
[ When you connect the machine to a computer for the first time ]
See "3. Setting Up for Use over Wired LAN".
When the machine has not been connected to the network, perform this setup to use the machine over wired LAN. This setup procedure requires settings to be performed on the machine and the computer.
[ When you connect the machine to an additional computer ]
See "4. Setting Up an Additional LANconnected Computer".
When the machine has already been set up to connect to the network, perform this setup to use the machine from an additional computer over wired LAN. This setup procedure only requires settings to be performed on the additional computer.
3. [ Setting Up for Use over Wired LAN ]
IMPORTANT
When the machine has not been connected to the network, to set up the machine to be used from a LANconnected computer, the necessary software must be installed on the computer. See "1. Preparing for Setup" and "2. Installing the Software" to confirm that the software installation is complete, then proceed with the procedure below.
3-1. On the Setup Method screen, select Set up the printer and the computer for network use, then click Next.
NOTE
If you select Use the printer via USB, the machine is set up to be used with USB connection.
3-2. ［When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine.
When you turn on the machine, the COPY button flashes green, then remains lit.
When the computer detects the machine, the next screen will appear automatically.
NOTE
- To set up the machine that is not yet connected to a wired LAN, connect the machine and the computer with a USB cable.
- If you cannot go to the next procedure after three minutes, see "Cannot Install the MP Drivers".
3-3. When the Setup Preparations dialog box appears, confirm that preparation is complete, then click Next.
NOTE
If the machine’s network settings are already configured, the Setup Environment Confirmation dialog box appears asking for your confirmation to use the machine with the current settings. You can proceed with the setup using the current network settings. To do so, click Use it as is. To reconfigure the network settings, click Reconfigure.
3-4. ［When the Check Wired LAN Connection dialog box appears, remove the LAN connector cap, connect the machine to the network devices such as hubs with a LAN cable, then click Yes.
(A) Wired LAN connector
(B) LAN connector cap
NOTE
The connection may vary depending on your network environment.
In Windows Vista, go to step 3-6.
In Windows XP and Windows 2000, go to step 3-5.
NOTE
If the machine was not detected, the Set Printer IP Address dialog box appears. Make sure of the following, then click Connect.
- The network devices such as hubs or routers are turned on, and the machine and the computer are connected to the network.
- The machine is connected to the computer with the USB cable.
- The IP address to be set for the machine is displayed on the Set Printer IP Address dialog box. If it is different from the address you want to set for the machine, select Use next IP address and enter the desired IP address. (If the machine is turned off, the Set Printer IP Address dialog box does not appear.)
3-5. When the Network Setup of the Card Slot dialog box appears, specify the drive letter,
then click Next.
This screen will not appear in Windows Vista.
NOTE
- The Card Slot of the machine must be mounted to be used as the memory card drive of the LANconnected computer. To write files to a memory card, set the Read/write attribute setting under Device settings to LAN enabled. If the setting is set to USB enabled, you cannot access the network drive of the Card Slot.
- If "Communication with the Card Slot failed." is displayed, click Retry.
- If "Cannot map any more drives, because all the drive letters are assigned." is displayed, click Skip to complete the setup. After software installation is complete, remove any drive letter and try the network setup of the Card Slot again using the Canon IJ Network Tool.
- If "The Card Slot is already mapped as Network Drive to this computer." is displayed, the Card Slot is already set up. Click OK, then click Next.
3-6. When the Setup Completion dialog box appears, remove the USB cable, then click Finish.
The network connection between the machine and the computer is now successfully established.
To confirm the setup results, click View Setup Results.
NOTE
- To change the port name, click View Setup Results, then click Set Port Name on the Setup Results dialog box.
- If "Unsafe Removal of Device" is displayed, click OK.
3-7. When the Setup Complete screen appears, click Next.
3-8. When the User Registration screen appears, click Next.
NOTE
- It is required to connect to the Internet to register your product. Turn on the firewall function before connecting your network to the Internet.
- To register later, click Cancel and go to step 3-10. After software installation is complete, double-click
on the desktop. - If a message asking for your confirmation to restart your computer appears, follow the on-screen instructions to restart your computer.
- The User Registration screen may not be displayed depending on the country or region of purchase.
If your network is connected to the Internet, the registration screen will appear. Follow the onscreen instructions to register your product. You will need your product serial number (A), which is located on the inside of the machine.
3-9. When the PIXMA Extended Survey Program screen appears, confirm the message.
We would appreciate it if you would take part in the PIXMA Extended Survey Program regarding the use of Canon printers. If you can agree, click Agree.
If Do not agree is clicked, the PIXMA Extended Survey Program will not be installed but you can use the machine normally.
3-10. The Installation completed successfully screen appears.
If only one CD-ROM is included in the packagefor the Windows setup
Click Exit.
The Setup CD-ROM will be ejected.
If it is not ejected automatically, remove it manually.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CD-ROM.
NOTE
Keep the CD-ROM in a safe place in case you need to reinstall the software.
If two CD-ROMs are included in the package for the Windows setup
When the Continue to Windows CD-2 screen
appears, perform the following steps (1) to (3) to
complete the installation.
(1) Click Exit.
The Setup CD-ROM will be ejected.
If it is not ejected automatically, remove it manually.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CDROM.
(2) Insert the Setup CD-ROM "Windows (CD-2) Macintosh".
(3) Follow the on-screen instructions to proceedwith the setup.
After installation is complete, the Setup CDROM will be ejected.
If it is not ejected automatically, remove it manually.
NOTE
Keep the CD-ROMs in a safe place in case you need to reinstall the software.
When using Windows Vista:
To use the Card Slot over network, mount the Card Slot using the Canon IJ Network Tool after software installation is complete.
4. [ Setting Up an Additional LAN-connected Computer ]
NOTE
To set up an additional LAN-connected computer, the necessary software must be installed on the additional computer. See "1. Preparing for Setup" and "2. Installing the Software" to confirm that the software installation is complete, then proceed with the procedure below.
4-1. Make sure that the machine is connected to the network device with a LAN cable, then turn on the machine.
When you turn on the machine, the COPY button flashes green, then remains lit.
NOTE
- If MAC address filtering is configured to restrict access to the machine, make sure beforehand to register the address of the computer you are setting up. To register the address, use the Canon IJ Network Tool on the computer that has already been set up.
- Make sure that the computer you are setting up is not connected to the machine with a USB cable. This setup procedure does not involve connecting the USB cable.
4-2. On the Setup Method screen, select Set up only the computer for network use, then
click Next.
The machine connected to the network is detected automatically.
4-3. Select the machine on the Printers dialog box, then click Next.
In Windows Vista, go to step 4-5.
In Windows XP and Windows 2000, go to step 4-4.
NOTE
If the machine has not been detected, make sure of the following, then click Update.
- The machine is turned on and connected to the network device with the LAN cable.
- The machine is not set to use access control (MAC address filtering).
- The firewall function of any security software is turned off.
Some programs that switch the network environment depending on your system environment will enable a firewall function by default. Check the settings on any such software.
4-4. When the Network Setup of the Card Slot dialog box appears, specify the drive letter,then click Next.
This screen will not appear in Windows Vista.
NOTE
- The Card Slot of the machine must be mounted to be used as the memory card drive of the LANconnected computer. To write files to a memory card, set the Read/write attribute setting under Device settings to LAN enabled. If the setting is set to USB enabled, you cannot access the network drive of the Card Slot.
- If "Communication with the Card Slot failed." is displayed, click Retry.
- If "Cannot map any more drives, because all the drive letters are assigned." is displayed, click Skip to complete the setup. After software installation is complete, remove any drive letter and try the network setup of the Card Slot again using the Canon IJ Network Tool.
- If "The Card Slot is already mapped as Network Drive to this computer." is displayed, the Card Slot is already set up. Click OK, then click Next.
4-5. When the Setup Completion dialog box appears, click Finish.
The network connection between the machine and the computer is now successfully established.
4-6. When the Setup Complete screen appears, click Next.
4-7. When the User Registration screen appears, click Next.
NOTE
- If you have already registered your product, click Cancel.
- It is required to connect to the Internet to register your product. Turn on the firewall function before connecting your network to the Internet.
- To register later, click Cancel and go to step 4-8. After software installation is complete, double-click
on the desktop. - If a message asking for your confirmation to restart your computer appears, follow the on-screen instructions to restart your computer.
- The User Registration screen may not be displayed depending on the country or region of purchase.
If your network is connected to the Internet, the registration screen will appear. Follow the onscreen instructions to register your product. You will need your product serial number (A), which is located on the inside of the machine.
4-8. When the PIXMA Extended Survey Program screen appears, confirm the message.
We would appreciate it if you would take part in the PIXMA Extended Survey Program regarding the use of Canon printers. If you can agree, clickAgree.
If Do not agree is clicked, the PIXMA Extended Survey Program will not be installed but you can use the machine normally.
4-9. The Installation completed successfully screen appears.
If only one CD-ROM is included in the package for the Windows setup Click Exit.
The Setup CD-ROM will be ejected.
If it is not ejected automatically, remove it manually.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CD-ROM.
NOTE
- Keep the CD-ROM in a safe place in case you need to reinstall the software.
If two CD-ROMs are included in the package for the Windows setup
When the Continue to Windows CD-2 screen appears, perform the following steps (1) to (3) to complete the installation.
(1) Click Exit.
The Setup CD-ROM will be ejected.
If it is not ejected automatically, remove it manually.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CDROM.
(2) Insert the Setup CD-ROM "Windows (CD-2) Macintosh".
(3) Follow the on-screen instructions to proceed with the setup.
After installation is complete, the Setup CDROM will be ejected.
If it is not ejected automatically, remove it manually.
NOTE
Keep the CD-ROMs in a safe place in case you need to reinstall the software.
When using Windows Vista:
To use the Card Slot over network, mount the Card Slot using the Canon IJ Network Tool after software installation is complete. For details, refer to "Using the Card Slot over a Network" in the User's Guide on-screen manual.
NOTE
- Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier are not supported, do not connect the machine to these.
- The screens below refer to Mac OS X v.10.4.x installation. Screens may vary depending on the operating system you are using.
- Log on as an Administrator.
- Quit all running applications before installation.
1. Connect one end of the USB cable to the computer and the other to the machine.
NOTE
Make sure the machine is turned on.
2. Turn on your Mac and insert the Setup CD-ROM.
NOTE
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon 
on the desktop.
on the desktop.3. Double-click the Setup icon.
4. When the Authenticate screen appears, enter your administrator name and password. Click OK.
If you do not know your administrator name or password, click 
then follow the on-screen instructions.
then follow the on-screen instructions.5. When the main menu appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed automatically.
NOTE
If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed with the installation.
6. When the list of applications to install appears, confirm the contents, then click Install.
NOTE
Move the cursor over items to display explanations of each application.
7. Read the License Agreement carefully and click Yes. The software installation screen may appear during the installation process. Read the contents on the screen and follow the onscreen instructions to install the software.
8. When the Setup Complete screen appears, click Next.
9. When the User Registration screen appears, click Next.
NOTE
- To register later, click Cancel and go to Step 10. After software installation is complete, double-click
on the desktop.
If your network is connected to the Internet, the registration screen will appear. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.
10. When the Installation completed successfully screen appears, click Restart.
After the computer restarts, remove the Setup CD-ROM.
When the computer restarts, the Canon IJ Network Tool will start up automatically.
NOTE
Keep the CD-ROM in a safe place in case you need to reinstall the software.
When using Mac OS X v.10.3.9:
Restarting the computer while connected to the machine may cause the machine not to be detected. To resolve this, either unplug the USB cable then plug it back in again, or turn the machine off then back on again.
NOTE
XXX FAX (where "XXX" is your machine's name) is shown in the Printer Name list (Product list in Mac OS X v.10.3.9), but you cannot add XXX FAX. You cannot send faxes from your computer via the machine.
11. When the Canon IJ Network Tool screen appears, select USB connection, then click OK.
NOTE
When using Mac OS X v.10.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications.
Software installation is now complete.
Setting Up the Machine and the Computer（Macintosh）
To use the machine connected to a computer, you need to install the software called "MP Drivers" in the computer.
[ Setting Up for Use over Wired LAN ]
(A) This machine
(B) Hub or router
(C) Computer
When the machine has not been connected to the network, perform this setup to use the machine over wired LAN. This setup procedure requires settings to be performed on the machine and the computer.
NOTE
- To set up the machine that is not yet connected to a wired LAN, connect the machine and the computer with a USB cable.
- Even if the machine has been set up to be used with the USB connection, follow the setup procedure described in this manual to connect the machine to a wired LAN for the first time.
[ Setting Up an Additional LAN-connected Computer ]
(A) This machine
(B) Hub or router
(C) Connected computer
(D) Additional computer
When the machine has already been set up to connect to the network, perform this setup to use the machine from an additional computer over wired LAN. This setup procedure only requires settings to be performed on the additional computer.
1. Preparing for Setup
Before installing the MP Drivers in your computer, make sure of the following.
- If the installation and adjustment of the machine have not been finished, refer to your setup sheet to set up the machine properly.
- Turn off the firewall function temporarily or change its setting. If you disable the firewall function, disconnect your network from the Internet. For information on the firewall function of your security software, refer to its instruction manual or contact its manufacturer.
IMPORTANT
After setup is complete, turn back on the firewall function you disabled for setup.
If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.
- Make sure that the configuration of computers, hubs, and other network devices is complete, and computers can connect to the network. The configuration and the type of the device vary depending on your network environment. For details, refer to your device’s instruction manual or contact its manufacturer.
IMPORTANT
A hub and LAN cable are required to connect this machine to a wired LAN. These must be purchased separately.
NOTE
- In an office setup, consult your network administrator.
- Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier are not supported, do not connect the machine to these.
- Log on as an Administrator.
- Quit all running applications before installation.
The screens in this manual refer to Mac OS X v.10.4.x installation. Screens may vary depending on the operation system you are using and also depending on the country or region of purchase.
2. Installing the Software.
To set up an additional LAN-connected computer, you do not need to connect it to the machine with a USB cable. Start from step 2-2.
2-1. Connect the machine and the computer with a USB cable.
(A) USB port
2-2. Turn on your Mac.
NOTE
Make sure that the machine is turned on.
2-3. Insert the Setup CD-ROM.
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon 
on the desktop.
on the desktop.
IMPORTANT
If two CD-ROMs are included in the package for the Windows setup, insert the Setup CD-ROM "Windows (CD-2) Macintosh" for the Macintosh setup.
2-4. Double-click the Setup icon.
2-5. When the Authenticate screen appears, enter your administrator name and password, then click OK.
NOTE
- If you do not know your administrator name or password, click
on the lower-left corner of the screen, then follow the on-screen instructions. - If the Select Language screen appears, select a language, then click Next.
- If the Select Your Place of Residence screen appears, select your place of residence, then click Next.
2-6. When the screen shown on the right appears, click Easy Install.
The MP Drivers, On-screen Manuals, and application software are installed automatically.
NOTE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.
2-7. When the Easy Install screen appears, confirm the contents, then click Install.
NOTE
- Move the cursor over items to display explanations of each application.
- The list of applications may vary depending on the country or region of purchase.
Users in Asia
- To view the User's Guide on-screen manual in a language other than the installed one, double-click the Manual folder in the Setup CD-ROM, Canon folder, and then copy a language folder to your hard disk.
2-8. Read the License Agreement carefully and click Yes.
Installation of the MP Drivers, On-screen Manuals, and application software will begin. The software installation screen may appear during the installation process. Read the contents on the screen and follow the on-screen instructions to install the software.
2-9. When the Setup Complete screen appears, click Next.
NOTE
The Setup Complete screen may not be displayed depending on the country or region of purchase.
2-10. When the User Registration screen appears, click Next.
NOTE
- It is required to connect to the Internet to register your product. Turn on the firewall function before connecting your network to the Internet.
- To register later, click Cancel and go to step 2-11. After software installation is complete, double-click
on the desktop. - The User Registration screen may not be displayed depending on the country or region of purchase.
If your network is connected to the Internet, the registration screen will appear. Follow the onscreen instructions to register your product. You will need your product serial number (A), which is located on the inside of the machine.
2-11. When the Installation completed successfully screen appears, click Restart.
The software installation is complete.
When the computer restarts, the Canon IJ Network Tool will start up automatically. Proceed with the network setup from following step 2-12.
After the computer restarts, remove the Setup CDROM.
NOTE
Keep the CD-ROM in a safe place in case you need to reinstall the software.
When using Mac OS X v.10.3.9:
Restarting the computer while connected to the machine may cause the machine not to be detected. To resolve this, either unplug the USB cable then plug it back in again, or turn the machine off then back on again.
NOTE
When using Mac OS X v.10.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications.
2-12. When the Canon IJ Network Tool screen appears, confirm the connection type.
The next procedure varies depending on how you intend to connect the machine and the computer.
3. [ Setting Up for Use over Wired LAN ]
When the machine has not been connected to the network, to set up the machine to be used from a LANconnected computer, the necessary software must be installed on the computer. See "1. Preparing for Setup" and "2. Installing the Software" to confirm that the software installation is complete, then proceed with the procedure below.
3-1. On the Canon IJ Network Tool screen, select LAN connection, then click OK.
If the Canon IJ Network Tool does not start up automatically, select Library > Printers > Canon > BJPrinter > Utilities > Canon IJ Network Tool.
NOTE
If you select USB connection, the Canon IJ Network Tool will exit without setting up the machine to be used over wired LAN.
– The machine is turned on.
– The machine is connected to the computer with a USB cable.
– The MP Drivers have been installed.
3-2. Select Setup in the pop-up menu, select your machine's name in Printers, then click OK.
NOTE
- If no printer is detected, click OK. Make sure of the following, then click Update.
– The machine is connected to the computer with a USB cable.
– The machine is turned on.
- If the machine’s network settings are already configured, the Setup Environment Confirmation dialog box appears asking for your confirmation to use the machine with the current settings. You can proceed with the setup using the current network settings. To do so, click Use as is. To reconfigure the network settings, click Reconfigure.
3-3. ［When the Check Wired LAN Connection dialog box appears, remove the LAN connector cap, connect the machine to the network devices such as hubs with a LAN cable, then click Yes.
(A) Wired LAN connector
(B) LAN connector cap
NOTE
The connection may vary depending on your network environment.
The machine connected with the USB cable is detected automatically via LAN connection.
NOTE
If the machine was not detected, the Set Printer IP Address dialog box appears. Make sure of the following, then click Connect.
- The network devices such as hubs or routers are turned on, and the machine and the computer are connected to the network.
- The machine is connected to the computer with the USB cable.
- The IP address to be set for the machine is displayed on the Set Printer IP Address dialog
box. If it is different from the address you want to set for the machine, select Use following IP address in TCP/IP Setting and enter the desired IP address. (If the machine is turned off, the Set Printer IP Address dialog box does not appear.)
3-4. When the Setup Completion dialog box appears, remove the USB cable, then click OK.
The network connection between the machine and the computer is now successfully established. The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.
3-5. On the Printer List dialog box, click Add.
In Mac OS X v.10.4.x, go to step 3-6.
In Mac OS X v.10.3.9, go to step 3-7.
In Mac OS X v.10.5, go to "Adding the Printer with Mac OS X 10.5"
NOTE
The machine displayed in the list is the one connectedwith the USB cable. You need to add the machine connected to the network to the list.
3-6.On the Printer Browser dialog box, click More Printers.
This screen will not appear in Mac OS X v.10.3.9.
3-7. Select Canon IJ Network in the pop-up menu, select your machine’s name in the list of printers, then click Add.
NOTE
The alphanumeric string after the machine’s name is its MAC address.
3-8. Confirm that your machine’s name is added to the list of printers.
3-9. On the Canon IJ Network Scanner Selector screen, select Canon XXX Network (where "XXX" is your machine's name) in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner. Confirm that a check mark is displayed, then click Exit to close the dialog box. The setup of the machine and the computer is complete.
4. [ Setting Up an Additional LAN-connected Computer ]
IMPORTANT
To set up an additional LAN-connected computer, the necessary software must be installed on the additional computer. See "1. Preparing for Setup" and "2. Installing the Software" to confirm that the software installation is complete, then proceed with the procedure below.
4-1. Make sure that the machine is connected to the network device with a LAN cable.
NOTE
- If MAC address filtering is configured to restrict access to the machine, make sure beforehand to register the address of the computer you are setting up. To register the address, use the Canon IJ Network Tool on the computer that has already been set up.
- Make sure that the computer you are setting up is not connected to the machine with a USB cable. This setup procedure does not involve connecting the USB cable.
4-2. On the Canon IJ Network Tool screen, select LAN connection, then click OK.
If the Canon IJ Network Tool does not start up automatically, select Library > Printers > Canon > BJPrinter > Utilities > Canon IJ Network Tool.
NOTE
If you select USB connection, the Canon IJ Network Tool will exit without setting up the machine to be used over wired LAN.
4-3. When the screen shown on the right appears, click OK.
4-4. Select Setup in the pop-up menu, then click Register Printer.
4-5. When the Cancel Setup screen appears, click Cancel.
The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.
If "You have no printers available." is displayed, click Cancel.
4-6. On the Printer List dialog box, click Add.
In Mac OS X v.10.4.x, go to step 4-7.
In Mac OS X v.10.3.9, go to step 4-8.
In Mac OS X v.10.5, go to "Adding the Printer with Mac OS X 10.5"
4-7. On the Printer Browser dialog box, click More Printers.
This screen will not appear in Mac OS X v.10.3.9.
4-8. Select Canon IJ Network in the pop-up menu, select your machine’s name in the list of printers, then click Add.
NOTE
- The alphanumeric string after the machine's name is its MAC address.
- If the machine has not been detected, make sure of the following.
– The machine is turned on and connected to the network device with the LAN cable.
- The machine is not set to use access control (MAC address filtering).
– The firewall function of any security software is turned off.
4-9. Confirm that your machine's name is added to the list of printers.
4-10. On the Canon IJ Network Scanner Selector screen, select Canon XXX Network (where "XXX" is your machine’s name) in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner. Confirm that a check mark is displayed, then click Exit to close the dialog box.
The setup of the machine and the computer is complete.
